Safe Operating Procedure Angle Grinder HS-SOP-031 – Logan WHS Wiki. Safe Operating Procedure - Angle Grinder Hs-sop-031 213.2k.
Bench and Pedestal Grinder Safety Tips 1. Stand to the side of the grinder when starting the electric motor. 2. Use the correct wheel for the material you are grinding, polishing, or buffing. 3. Adjust the tool rest as close as possible to the grinding wheel without touching it. It must have a gap of between one-sixtinth and one-eighth inches. 4.
Operating Procedure 1. Inspection Before using the polisher/grinder inspect it and its surroundings for the following: C Make sure the electric power connections are made correctly and that the power cable is not damaged. C Make sure the polisher/grinder, including the wheel and the bowl, are clean. C Make sure the table and the floor around the table are clean and dry.
Safe operating procedures are the 2nd stage in effective risk management, and are an effective and proven method for communicating (and documenting) the correct way of using a tool or piece of equipment or carrying out an activity within your workplace. It is a training tool, and is a control used to minimise a hazard.
The tool post grinding machine, see Figure 5-5, is a machine tool attachment designed to mount to the tool post of engine lathes. It is used for internal and external grinding of cylindrical workplaces. Refer to Chapter 7 for a description of this machine. 5-3. TC 9-524
sop tool grinding. Safety Policy and Procedure - Cianbro. 7.1.5 Ensure team members have been trained for the specific tool they are going to use. 7.2 Right Tool for the Job 7.2.1 Ensure the correct type of grinding wheel is used for the work that is to be done. Refer to the manufacturer's literature for appropriate use of the different ...
The dependent variable is the compliance of the Site Operational Procedure (SOP) of the Grinding Tools tool. Data collection techniques such as questionnaires, and observation. The analytical methods used include quantitative descriptive analysis. Result: Found 27 (50%) of 54 respondents comply with SOP.
STANDARD OPERATING PROCEDURE 'S.O.P'. Keep all guards in place while operating the machine. While operating the milling machine allow no one else to touch it. Keep hands away from moving cutting tools. Do not make …
grind. Keep hands away from grinding wheels at all times. Adjust the tool rests a maximum of 3mm away from wheels and slightly below centre. Bring object into contact with grinding wheel slowly and Do not grind on the side of the wheel. Slowly move the work piece across the face of the wheel in a uniform manner to prevent 'ruts' or grooves from
Inspect grinding disc for signs of wear and damage per tool safety checklist, replace if necessary and dispose of used disc blades appropriately. Angle grinder operation per angle grinder SOP focuses on angle grinder control measures to reduce the level of risk. Workplace environmental hazards, e.g. confined space and working at heights.
touching it. The tool rest must be minimally within 1/8th of an inch of the grinding wheel. • Prior to starting the grinder, ensure the tang at the top of the wheel opening is located within ¼ inch of the wheel. • Prior to starting the grinder, ensure guards enclosing the outside of grinding wheel are in place.
SOP NO. IMFA/SOP/SMC/MINING/01 REVISION 00 EFF DATE: 19.6.14 NO. OF PAGES Page 8 grinding tool .Connect one end of the air hose to the nipple provided at the main air line and the other end to the grinding tool . Place the bit to be grinded vertically in the groove in the grinding table. Fix the grinding stone on the grinding tool.
7.1 Correct Tool Selection If a grinder must be used, chose the right grinder for the job. Do not use a larger, heavier, or more powerful grinder than is necessary for the job as it is much easier to lose control of it. The posture and positioning of the operator must be consider will determining the appropriate tool for the job. 7.2 Disc Safety
Keep tools sharp and clean for better and safer performance. Follow instruc-tions for lubricating and changing accessories. n DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, grinding wheels, etc., all tools should be disconnected. n AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in any tool.
This SOP should be used in conjunction with relevant machinery manuals and manufacturer recommendations. Procedure Reference Version Effective Date Review Date Page Number Date Printed WHS SOP 19 1.0 28/03/2018 28/03/2021 1 24/04/2018 SOP 19 – Electric Arc Welder – Small Welding Jobs
Ensure tool rests are not more than 2mm away from grinding wheels - Avoid pinch points Ensure cooling dish has ample water in it – Cool parts often ... Student Support and TrainingHealth and SafetySOP'sSOP_Grinder - Pedestal and Bench Grinder.doc 2. Operation:
Normally, a part is held in a collet or lathe chuck and a cutting tool is held in a tool post. The lathe is switched on and the part begins to rotate. The cutting tool is then brought to the rotating part and removes material. The goal of this SOP and the accompanying "training" is not to make you a lathe operator/machinist, but to make sure
a good foothold is available for persons using power tools. Ensure that flammable liquids or other readily ignit ed materials are cleared from area, or covered t o protect from grinding sparks. Observe restrictions. Prevent sparks from entering or affecting adjacent work areas. Restrict entry into area where grinding is to be carried out.
• SOP 36 Sample Preservation, storage, and shipment • Any future SOPs dealing with subsurface sampling ... This would include loss of circulation, sudden tool drops, unrecovered tools in the borehole, and lost casing. • The dates for the start and completion of borings will be recorded on the Drill_Log form.
WHS SOP 2 1.0 28/03/2018 28/03/2021 1 24/04/2018 SOP 02 – Bench Grinder DO NOT use this tool unless appropriately instructed in its safe use and operation and permission to operate has been given. COMPULSORY PPE AS NEEDED PPE PRE-OPERATIONAL SAFETY CHECKS 1. Check workspaces and walkways to ensure no slip/ trip hazards are present. 2.
the storm sewer system or local streams. This SOP has been written to describe best practices for control of the wet saw cutting wastewater. 2.0 Scope . This procedure applies to wet sawing, grinding, and drilling/coring by Facilities operations Management (FM) personnel and contractors. 3.0 Responsibility
Reinforced Weld Grinding Wheel, PN 01991 3M™ Cut-Off Wheel Tool, 3 in., PN 33579 3M ™ Cubitron II File Belt, 1/2 in. x 18 in., grade 80+, PN 33446 Aluminum Panel Removal 1 Clean Clean the panel prior to disassembly with soap and water followed by a VOC compliant surface cleaner. 2 Sealer/Coating Removal If necessary, use a Scotch-Brite ...